Installation, dismantling of partitions in the apartment. Dismantling the partition between the bathroom and the toilet. Dismantling the partition under the ceiling in the corridor

If you are thinking about repairing and want to make itbudget, then for this there is no need to use the services of a professional team of builders. But the dismantling of the partition and you can do it yourself. The main condition in this case is that it is forbidden to touch the load-bearing walls. This approach allows you to make redevelopment, increasing the space of a particular room and achieving maximum comfort.

Which partitions can be dismantled

Demolish partitions of the following materials without fear:

• brick;
• concrete;
• foam block;
• a rock;
• wood;
• drywall.

However, for each of the listed materialsits own rate of demolition is provided. To perform the dismantling of the wooden wall, you need to apply less effort than required if the apartment has solid walls. When it is difficult to determine which material is the basis, you should seek professional advice. Incidentally, in this case, they recommend that you do a dismantling of a certain part of the wall, which will allow you to see the material in the composition, which allows you to determine the nature of the upcoming works.

Preparation

If you started dismantling the partition, thenit is necessary to carry out preparatory work. To do this, all communications are turned off - heating, water, radio, electricity, sewage and gas. It is also necessary to take care of where you will put the construction debris. For this, bags are usually prepared.

Preparation of tools

The dismantling of the partition necessarily involves the preparation of a specific set of tools, namely:

• chisel;
• wedges;
• a jackhammer;
• pickaxes;
• crowbar;
• sledge hammers.

If you have to work with woodpartition, then you can put a chainsaw in motion, replacing it with a jackhammer. But as for the concrete partition, it can be disassembled with a jackhammer, a perforator or a Bulgarian. Such a serious set of tools is required for the reason that inside the concrete wall there is a metal frame, for the elimination of which an angle grinder is needed.

Carrying out the dismantling of the partition

Dismantling the partition can be started immediatelyafter the completion of the preparatory work. The master should submit a cardboard box, which will need to be removed from the wall. It should be guided by the principle of cutting a certain part of this box. If you remove the partition on the perimeter, then its middle part can collapse on the floor, and you will subject the floor to a load of several hundred kilograms. It is important to remember that you can not dismantle large pieces of walls. First of the partition you need to knock out one brick, and then - remove the door jumper, gradually moving to the edges. If you have a brick wall in front of you, then there will be enough sledgehammers. Begin to handle such a partition is necessary from the ceiling.

Demolition of the partition between the toilet and the bathroom

Dismantling the partition between the bathroom and the toiletis carried out in several stages. On the first you need to remove the panel or tile, if you plan to use the finish again. Above the upper row of the masonry, in the interval between the ceiling and the finishing material, it is necessary to drive a chisel or chisel, loosening the bricks. This will remove the product from the wall. If there is a vent hole, the dismantling must begin with it.

Nail should be used as a lever,it is driven into the cracks in the masonry. This method eliminates the formation of a large amount of dust, and work can be done with minimal noise. Most of the bricks remain intact, they can be used later. However, such a scheme of dismantling partitions takes a long time, and the process can be accelerated using a perforator. A sledge hammer or chisel is mounted on the tool, however, there will be more noise and dust. In this case, the bricks turn into debris.

If the partition has a plaster in the base, then byperimeter it is necessary to make the cuts, breaking the material with a sledgehammer. The inside fitting must be cut by an angle grinder. As soon as you manage to remove the partition, you need to start dismantling the skirtings, which are the foundation for the gypsum box. They can be made of concrete, reinforced with rods. Therefore, for dismantling work, you should use a grinder or a puncher.

Recommendations of a specialist

Dismantling partitions in an apartment canaccompanied by the need to remove the wall of concrete. To do this, you need to make a markup on the surface, and after using a grinder and a disc to cut out small pieces. The same technology should be used when there is a need to dismantle the partition under the ceiling in the corridor. To do this, you can use an impact drill or a perforator, drilling holes located close to each other. Then the surface rattles lightly along the holes, and the resulting debris should be broken off.

Baffle installation

Entering into a new apartment, the owners of housingthey often ask themselves how to install a partition. For carrying out of similar works it is possible to use different materials, including foam concrete blocks. It is important to choose the right material, which can be heat-insulating, structural-heat-insulating and structural. For the construction of partitions, it is best to use blocks marked D600 or higher.

In addition, you should prepare the glue. There is a huge variety of industrial compounds that are used for laying foam blocks. Mixtures are made on the basis of Portland cement, fine quartz sand and plasticizers.

Mounting / dismantling partitions quite oftenIt is carried out by new tenants of apartments independently. If you decide to erect a partition from a foam concrete block, then its lower surface must be smeared with glue and placed on the floor. The first and last products, which will be in contact with the wall, should be additionally fixed with a metal corner.

Conclusion

Sometimes the length of the foam concrete block isnot enough to lay a whole row. In this case, you can cut out the additional elements with a hand saw. The second and subsequent rows of products should be staggered, observing the dressing of the joints. The thickness of the adhesive layer should not exceed 5 mm, and the application of the mixture should also be carried out on a vertical surface.

</ p>>