Crash 711 (error): how to fix it?
Quite often, many computer usersWindows-based systems face an unpleasant problem when, when trying to connect to the Internet, an error occurs with the code 711 (error) instead of the expected connection. How to fix it in a few simple ways, now it will be shown.
Causes of a malfunction
If you understand, the reasons for the appearance of suchmalfunctions can be quite a lot. However, there are several typical cases, which are mainly related to the disruption of a number of services responsible for making remote access connections, as well as components related to PPPoE telephony (this is especially often when using a connection through a VPN).
Therefore, the failure occurs because the following services can be disabled:
- Plug & Play support service (self-tuning devices);
- dispatchers standard and automatic connection of remote access;
- telephony service;
- SSTP service (for Windows 7 and later only).
In parallel, we will consider several more optionsfailure 711 (error). How to fix the situation will be given for each specific case. In addition, it will not be given a very standard recommendation, which can be used, so to speak, in extreme cases, and then only at your own peril and risk.
Error 711, Windows 7: How to fix it in the Services section?
So, first we need to test the workof the above components. You can do this from the administration section found in the standard "Control Panel", but it will be faster to use the "Run" menu, in which you should write the services.msc command.
Now we find each of the above services inthe list on the right and the right click call the submenu, where we select the property section. Here you need to pay attention to the type of launch. To support Plug & Play devices, you must set the automatic start, and for all others - start manually. At the end of changing the parameters, we save everything and overload the system.
Connection error 711: how can I fix it with advanced permissions?
Unfortunately, only non-working componentsservices business can and not be limited. Another reason may be that the user has insufficient access rights to the system. In this case, fault 711 (error) will appear again. How can I fix it if the previous solution does not work? Yes, it's very simple.
We use the standard "Explorer", on the system(most often it's a "C" partition), we find the Windows folder, right-click the context menu and select the property section from there, and then go to the security tab.
Here we are interested in the "System" line. A little lower click the change permissions button, and in a new window we look at user groups. For groups CREATOR-OWNER, "SYSTEM" and "TrustedInstaller" we apply the button for changing parameters, then we indicate full access (in the window below we put "birds" opposite all available items). Save the changes and again perform a reboot.
Rename the LogFiles folder
It is often enough to meet anothersituation related to the report files. There may also be a 711 error (error). How to fix the problem in this case? Yes, just rename the folder where this data is stored.
As a rule, the catalog itself can be found in thefolder System32 root directory system (Windows). But first you should boot either in safe mode, or use some LiveCD (in normal mode, the system will not be able to rename the folder).
Boot, find the desired directory andassign it a name at its discretion (Logfiles 1, Logfiles_1, yes anything). The main thing is to leave the original name in the title with the addition of something else). Next, as usual, you need to reboot, that's all.
Command line at own risk
Finally, let's see how to fix 711 errorconnection of the Internet with the help of a special team. Immediately note the fact that experts recommend using it only in situations when nothing else helps.
We call the command line (cmd in the "Run" menu(Wind + R)), and then register the sequence shown in the figure in it, and press the enter key. This command allows to restore the standard rights and security permissions for system folders. Then we reload the computer terminal in the usual mode. In theory, after applying such a cardinal method, there should not be any problems.
Conclusion
As can be understood from all of the above, specialreasons to worry, in principle, no, because the very error for the system is not critical. Yes, and considered here the most typical failures. In theory, because the system services, presented in the first section, should not be disabled by themselves, which means that the error is caused by something else. Who knows, maybe this is the impact of viruses or the usual interference in the operation of the user's system with administrator rights, which does not possess the necessary knowledge. But in general, as you can see, the problem is solved quite simply.
</ p>>
