How to glue a tint?
You have a favorite car and you wantmake it even more attractive zatonirovuv glasses? Do you think this is very difficult and you can not cope without the help of a master? After reading this article, you will realize that you have made a big mistake and will find the answer to the question "how to glue toning?"
Every driver loves his car, he's about itcares, cleans, washes and decorates. Tinting until recently was an essential accessory for most cars. The color and throughput of the tinted glass, before the adoption of the latest amendments to the traffic rules, were a personal matter for every motorist. The changes introduced in the code of road regulations today govern the permissible obscuration. According to the new resolution, the throughput capacity of the windscreen should be at least 75%, the side viewing glasses - at least 70%. Violation of these standards leads to an administrative penalty. This must be remembered.
How to glue a tint
If you still decide, you should notbuy a cheap film: it is excessively thin and in the kit you will not find a special knife and spatula, which will have to be purchased separately. For gluing you will still need a dry rag, a liquid for washing glasses and a siphon, in which the same means for washing glasses is poured.
Now that everything is prepared, you canproceed directly to the process of toning. Work should be done in a warm room and preferably with an assistant. If the film is glued on the street, it is recommended that all actions be carried out in a calm weather, at a temperature not lower than +20aboutFROM. The glass should be thoroughly washed with a substance containing alcohol. It cleans and degreases the surface well. After the glass has dried, a tint film is applied. Here you need to be careful: do not cut the material strictly along the contour. On all perimeter it is necessary to leave allowances in 3-4 cm.
The film corner is carefully tucked away and separated from thebasis. With the siphon, spray the diluted solution on the dark side to avoid gluing. The separated dark layer is applied to the glass and carefully smoothed out with a plastic spatula. The direction of movement of the spatula should be from the center to the periphery. From time to time, the film should be wiped with a damp cloth. The excess protruding edges are cut with a sharp knife, which should be included. The side windows are also toned.
Now it remains to understand how to properly glueTinted on the rear window. Not all drivers can correctly position the film without removing it from the machine. On cars VAZ the cord is removed, and the glass is squeezed out. Since it is inconvenient to work (due to its convex shape), the procedure is divided into two stages. The imaginary line divides the glass into two parts. A film is applied to one half. It is cut with the same allowances as on the side windows (2-3cm). If creases are formed, you will need a building hair dryer. He heats the film and stretches out until there is no wrinkles. The second part needs to be glued exclusively in the joint and nothing else. At the end of the work, the glass is put in place.
Now it became fashionable to tune not only glass,but headlights and headlights. Such toning of headlights is a laborious process and, moreover, absolutely useless. After all, over time, the edges of the film will begin to exfoliate and reduce all the work to naught. Also, apply a vinyl film to the hood, trunk or wings of the car, which makes your car not only beautiful, but also original.
We figured out how to glue toning. In this there is nothing complicated. It takes only a little patience and a sharp knife. But do not overdo it with darkening. It is better to glue the film only on the rear windows. Remember that for violation of the requirements of PPD for window tinting, a fine of 500 rubles is provided, and from 1 July 2012 - it is possible to withdraw the numbers.
For your information! The size of the penalty does not depend on how many glasses are covered with a darkened coating and what is the light transmission capacity of the "native" glasses of the machine. So decide for yourself whether you need to know how to glue toning.
</ p>>
