Replacement of the front stand VAZ-2109 with your own hands: the repair procedure

To replace the front pillars on the VAZ-2109It is necessary if there are breakdowns in them. From these suspension elements depends comfort, and most importantly - traffic safety. If you operate a machine with worn-out struts, this will cause the body to gradually break down. If there are small cracks on the windshield, they will increase. The front panel can also collapse. But it's nothing compared to what loads the body elements feel.

Symptoms of rack failure

To understand that you need to replace the front pillars, you need to pay attention to the main signs of breakdowns. There are a few of them:

1. Presence of oil stains on the shock absorber body.
2. Mechanical damage to the front pillar elements.
3. Destruction of the spring.
4. Bearing wear.

Check the condition of the front pillar can be, if you sharply press on one side of the car, forcing the spring to fully compress. The body must return immediately to its original position and stop.

If he continues to hesitate, it speaks ofThe fact that the suspension works on springs alone. The shock absorbers are faulty, so the car body continues to move. In the event that you have identified a breakdown of the shock absorber, you will need to replace the front post on the VAZ-2109. With your own hands all the work can be done quite simply.

Tools for repairs

To do all the work correctly, you will need the following tool:

1. A jack, and it is desirable to use podkatnye hydraulic or pneumatic.
2. Support under the car.
3. Wheel chasers.
4. Spring puller.
5. A set of keys.
6. Penetrating grease.
7. The puller for the tip of the steering rod.
8. Pliers.

It is also desirable to have a workbench with good grips, so as to dismantle the front rack without problems.

What you need to buy for replacement

Before you replace the front post on the VAZ-2109, you will also need the availability of spare parts. It is necessary to purchase the following items in specialized stores:

1. Shock absorber. It is advisable to select items from well-known manufacturers to improve the performance of the car's suspension. To save, you can use standard shock absorbers, which were installed in the factory.
2. Rubber or silicone bumpers placed on the shock absorber rod.
3. Anthers, preferably rubber, not plastic.
4. New bolts and nuts.
5. Springs, if the old ones are damaged.
6. Support bearings installed at the top of the rack.

It is also desirable to purchase new rubbercushions to improve the operation of the car. If you want, you can buy a ready rack assembly. To mount it, it is enough to completely throw out the old one and put a new one in its place. Installation of such a device will be much easier, and the efficiency of work is higher.

Removing the rack

Before starting work, be sure to do the following:

1. Install wheel chocks under the rear wheels.
2. Lift the repaired side, first loosen the wheel fastening.
3. Remove the wheel completely.
4. Then it is necessary to unscrew the two nuts from the bolts that secure the shock absorber to the wheel hub.
5. Take the brake tube aside so as not to damage it.
6. Remove the cotter pin from the hole in the steering tip, then unscrew the nut on it.
7. Install the puller and pull the steering tip from the steering knuckle.
8. With a key of 10, unscrew the three nuts that secure the bearing to the glass on the body. This work needs to be done from the engine compartment.
9. After carrying out these works, you can easily dismantle the rack.

If necessary, the repair or full replacement of the VAZ-2109 front post is carried out. A photo of this suspension element is given in the article.

How to disassemble the front pillar

In order to completely disassemble the front rack VAZ-2109, you need to perform the following actions:

1. Install the tensioning device on the spring.
2. Evenly compress at least three turns of the spring.
3. With a key on 17, unscrew the nut on the shock absorber rod. The stock must be secured from scrolling.
4. Remove support bearing, spring, rubber elements.

On this, the racks are dismantled. It is not recommended to reuse rubber elements, as they have lost their quality. Be sure to install new bumpers, anthers, cushions. Some models of shock absorbers can be completely disassembled and carry out their repair.

But such actions are hardly advisablecarry out, because to carry out quality repairs will not be able to every experienced car mechanic, what can we say about amateurs. After all, you need to completely disassemble the shock absorber, replace all worn out items, rinse the internal surfaces thoroughly, then pour oil inside.

Here with the last point there can be problems -if you pour a few grams less, the shock absorber's work will turn out to be wrong. If you pour a little more, then the oil seals will collapse. Therefore, it is best to perform a complete replacement of the VAZ-2109 front post, rather than to carry out several expensive repairs. After installing new racks, be sure to correct the camber angles and the convergence of the wheels.

</ p>>